If anyone else has the same issue, look for. I had an. It was forcing a version of PHP that was not installed on my local machine. Thus the virtual host wasn't executing the PHP file properly. This is almost certainly the problem if some sites work and others don't. Show 1 more comment. After struggling a lot I finally solved the problem.
But If you are still getting the error : Config file php5. Ravi Shankar Ravi Shankar 1 1 silver badge 5 5 bronze badges. Note that this only works under Linux and specifically Debian Linux. Please take a look at your addtype directives. Clearing your browser cache is always a good idea. AddHandler php5-script. DirectoryIndex index. Sam Azer Sam Azer 3 3 bronze badges. The problem here is that PHP is not being run correctly somehow, or the wrong headers are being sent Note the last AddType directive which is commented out in the above example, causes a.
Is it possible that your Apache configuration is pretty-printing. You can begin installation of modules like, sudo apt-get install libapache2-mod-php7. Noushad Noushad 4, 3 3 gold badges 22 22 silver badges 27 27 bronze badges. Thanks to all!!! Ladislao Garcia Ladislao Garcia 62 2 2 bronze badges.
Take care of browser cache too. My system : Ubuntu Do NOT set it to On as it prevents. In case someone is using php7 under a Linux environment Make sure you enable php7 sudo a2enmod php7 Restart the mysql service and Apache sudo systemctl restart mysql sudo systemctl restart apache2. MedoAlmasry MedoAlmasry 3 3 silver badges 18 18 bronze badges. Jeffrey Bosboom Craig Smilovitz Craig Smilovitz 13 3 3 bronze badges.
Marouen Mhiri Marouen Mhiri 1, 1 1 gold badge 13 13 silver badges 20 20 bronze badges. The conclusion If I commented these two lines out in my.
The entire story I have VirtualMin installed on an Ubuntu I tried all kinds of stuff: Removed PHP7. Tried enabling and disabling apache modules, on the existing installation, but without luck. Then I removed apache completely and installed it again, where-after the problem was still there!
And I found the module name by Googling around. I had to active about modules, before I got past that step in the validation - and it took a couple of minutes before the cache ran out, - so doing this was a tedious step. And lastly, I figured out above-written conclusion - together with the symlinks, - and then I got it to work.
I had to go through it for every site on my VPS, though. Zeth Zeth 1, 2 2 gold badges 29 29 silver badges 59 59 bronze badges. Dia Dia 1 1 gold badge 2 2 silver badges 15 15 bronze badges.
TomoMiha TomoMiha 1 1 gold badge 11 11 silver badges 11 11 bronze badges. I had constructed a test. Slip Slip 1 3 3 bronze badges. If none of the above works, try commenting out the line SetHandler Arun Panneerselvam Arun Panneerselvam 1, 1 1 gold badge 15 15 silver badges 21 21 bronze badges. Then I check PHP is enabled. I check installed PHP packages.
I think this will help anyone. Janaka Pushpakumara Janaka Pushpakumara 4, 3 3 gold badges 23 23 silver badges 30 30 bronze badges. Black Black 14k 29 29 gold badges silver badges bronze badges.
When i upgraded from PHP 7. Worked by doing following:- In [domain]. Note: In the above write-up, spacing had to be added because it was otherwise not showing up on the screen.
When copying the code, remove the spacing. Your email address will not be published. Save my name, email, and website in this browser for the next time I comment. Any requests in progress are terminated, and no further requests are served. The USR1 or graceful signal causes the parent process to advise the children to exit after their current request or to exit immediately if they're not serving anything.
The parent re-reads its configuration files and re-opens its log files. As each child dies off the parent replaces it with a child from the new generation of the configuration, which begins serving new requests immediately. This code is designed to always respect the process control directive of the MPMs, so the number of processes and threads available to serve clients will be maintained at the appropriate values throughout the restart process.
Furthermore, it respects StartServers in the following manner: if after one second at least StartServers new children have not been created, then create enough to pick up the slack.
Hence the code tries to maintain both the number of children appropriate for the current load on the server, and respect your wishes with the StartServers parameter. The code was written to both minimize the time in which the server is unable to serve new requests they will be queued up by the operating system, so they're not lost in any event and to respect your tuning parameters. In order to do this it has to keep the scoreboard used to keep track of all children across generations.
The status module will also use a G to indicate those children which are still serving requests started before the graceful restart was given. At present there is no way for a log rotation script using USR1 to know for certain that all children writing the pre-restart log have finished. We suggest that you use a suitable delay after sending the USR1 signal before you do anything with the old log.
For example if most of your hits take less than 10 minutes to complete for users on low bandwidth links then you could wait 15 minutes before doing anything with the old log. When you issue a restart, a syntax check is first run, to ensure that there are no errors in the configuration files. If your configuration file has errors in it, you will get an error message about that syntax error, and the server will refuse to restart.
This avoids the situation where the server halts and then cannot restart, leaving you with a non-functioning server. This still will not guarantee that the server will restart correctly.
0コメント